mobile-main-menu-button
Menu

How can we help? What do you want to learn? Search our knowledgebase.

Potentiostat/Software Installation Quick Start

Last Updated: 10/28/20 by Tim Paschkewitz

Download as PDF
ARTICLE TAGS
  • installation,
  • new potentiostat,
  • first use,
  • quick start,
  • software installation,
  • drivers,
  • order of operations,
  • initial setup
Article Contents/Section Navigation
  1. Initial Setup and Installation of New Potentiostat
    1. Step 1: Find the User Guide
    2. Step 2: Leave the Potentiostat in the Box
    3. Step 3: Obtain the USB Flash Drive
    4. Step 4: Install AfterMath Software
    5. Step 5: Install Device Driver
    6. Step 6: Connect Potentiostat to Computer by USB Cable
    7. Step 7: Power On Potentiostat
    8. Step 8: Start AfterMath
    9. Step 9: Verify the Status of the Potentiostat in AfterMath

1Initial Setup and Installation of New Potentiostat

READ ME.  We want your instllation process to be fast and efficient.  it is essential to first install software and drivers before you connect the potentiostat to the computer.  Follow the Quick Start Installation instructions below.

Because all of our potentiostats interface to PCs by USB, when Windows® detects that a device is connected by USB, it immediately searches for what it thinks is the most appropriate hardware driver.  Unfortunately, in many cases, Windows selects the incorrect driver and associates it with your new potentiostat.  Then, when you start AfterMath, you may notice that the potentiostat is not found and there is a red or orange blinking LED on the potentiostat.  This is most likely caused by an incorrect driver association.  To avoid this, follow this quick guide and adhere to the order of operations, to ensure the correct driver is installed, making your potentiostat ready to use for electrochemical studies.
Back To Top

1.1Step 1: Find the User Guide

This is typically a black binder located inside the main box or within the inner box if present.
 
WaveDriver 200 Integrated Bipotentiostat with EIS User Guide

Figure 1. WaveDriver 200 Integrated Bipotentiostat with EIS User Guide

Back To Top

1.2Step 2: Leave the Potentiostat in the Box

You will not need the instrument yet.  Keep it safe until required in later steps.
 
Pine Research Instrumentaiton Shipping Box

Figure 2. Pine Research Instrumentaiton Shipping Box

Back To Top

1.3Step 3: Obtain the USB Flash Drive

It is located in a plastic flap inside the user guide.  Connect it to your PC.
 
Pine Research Potentiostat Installation Media (USB Flash Drive)

Figure 3. Pine Research Potentiostat Installation Media (USB Flash Drive)

Back To Top

1.4Step 4: Install AfterMath Software

Double-click the Windows Installer Package named “Setup” as shown below.
 
Installation of AfterMath

Figure 4. Installation of AfterMath

Back To Top

1.5Step 5: Install Device Driver

During the course of AfterMath installation, you will be prompted to install the device drivers.  Proceed by clicking Next:
FTDI USB Device Driver Installation Dialog 1

Figure 5. FTDI USB Device Driver Installation Dialog

 
Verify the drivers were installed as shown in the complete dialog:
 
FTDI USB Device Driver Installation Dialog 2

Figure 6. FTDI USB Device Driver Installation Complete Dialog

 
Continue through any remaining steps to finish the installation.
Back To Top

1.6Step 6: Connect Potentiostat to Computer by USB Cable

Now that AfterMath software, instrument drivers, and support software have been installed, carefully unpack the potentiostat and connect it to your computer with the supplied USB cable.
 
Connecting the USB cable between WaveDriver 200 and PC

Figure 7. Connecting the USB cable between WaveDriver 200 and PC.

Back To Top

1.7Step 7: Power On Potentiostat

Upon turning the potentiostat on, you should notice a Windows® notification (popup and/or sound) indicating that it detected new USB hardware.  Wait about 30 seconds before proceeding to step 8.
 
WaveDriver 200 with AC adapter connected and potentiostat powered on

Figure 8. WaveDriver 200 with AC adapter connected and potentiostat powered on.

Back To Top

1.8Step 8: Start AfterMath

You may have selected to place a shortcut on your desktop.
 
If not, find where AfterMath was installed on your computer.  Most commonly, the location is:
 
C:\Program Files (x86)\Pine\AfterMath
 
Open/start the aftermath.exe application in the folder.
Back To Top

1.9Step 9: Verify the Status of the Potentiostat in AfterMath

View the connected instruments in AfterMath.  You should observe an entry for the potentiostat with its serial number in the Idle state.
 
Connected WaveNow Potentiostat shown in AfterMath Software

Figure 9. Connected WaveNow Potentiostat shown in AfterMath Software

 
Finished! If you have any issues or need further assistance, please contact us.
Back To Top
Questions? Find Answers.

Our knowledgebase is the central repository for written content, including help topics, theory, application notes, specifications, and software information.

Select a category below or view the Knowledgebase home page
Software

Detailed information about our Software, which includes AfterMath and retired PineChem.

Applications

Application notes discuss practical aspects of conducting specific experiments.

Theory

Fundamental electrochemical theory presented in a brief and targeted manner.

Product Specifications

Review complete product specifications and compare products within a category here.